Pearl Elite Support

Pearl PTM Solenoid replacement disassembly and cleaning

download the PDF on the Pearl PTM Solenoid replacement disassembly and cleaning

Pearl Elite Solenoid Replacement disassembly and cleaning

Download the PDF on the Pearl Elite Solenoid Replacement disassembly and cleaning

Pearl Elite - Troubleshooting

If you experience Possible Causes Solution Leaks Pretreatment solution dripping from Solenoid Hose may have come loose. Push hose in to quick connect Excessive pretreatment solution dripping from nozzle Nozzle Cap is loose Tighten Nozzle Cap Nozzle O-Ring is not installed Install Nozzle O-Ring Check Valve is not installed Install...

Pearl Elite - Adjustments

If desired operation is not within the range of factory default settings, platen height, viscosity setting, fan timing, and auto prime timing can be adjusted. 1. Adjusting Platen Height The Platen height can be adjusted to set the desired amount on the shirt. Raising the platen will bring the spray...

Pearl Elite - Cost Calculations

 The Pearl Elite is equipped with a cost calculator that allows users to determine the cost of pretreatment used on a single shirt or the cost for a run of shirts. 1.Entering Pretreament Cost: Enter the Stats Menu by pressing the Stats Menu icon. Press the Cost/Gal # for either the...

Pearl Elite - Save Settings

 The Pearl Elite has a save feature that allows users to save settings and modes. The save feature will allow up to twenty files to be stored in the memory of the machine. 1. To save the current settings, open the Save Menu by pressing the Save Menu icon. 2. The...

Pearl Elite - Keeping the Pearl Elite Clean

It is important to keep the Pearl Elite clean during extended use. The pretreatment solution can build up salt deposits that can inhibit normal operation of the Pearl Elite. It is recommended to clean the inside of the Pearl Elite after every use to prevent build up of pretreatment that...

Pearl Elite - Power Down

The Pearl Elite stores setting and cycle information, as well as estimated pertreatment container levels during power off. It is important to follow these shut down procedures to allow this information to be stored correctly. The Pearl Elite will not allow the unit to properly power down with pretreatment solution...

Pearl Elite - Flushing the Pearl Elite

When anticipating extended periods of non-use of the Pearl Elite, it is critical to follow these maintenance procedures. It is required to follow these steps daily after each use of the Pearl Elite. 1. To flush the Pearl Elite, enter the Maintenance Menu by pressing the Maintenance Menu icon. 2....

Pearl Elite - Changing Pretreat

When changing pretreat it is important to follow these steps to ensure proper function the the Pearl Elite. The internal volume (mL) counters use these maintenance buttons to calculate the estimated usage. 1. To change the pretreat, enter the Maintenance Menu by pressing the Maintenance Menu icon. 2. Remove the...

Pearl Elite - Spray Cycle

The Spray Cycle is the process the Pearl PTM uses to lay a flat and even layer of pretreatment solution on to the garment. 1. To begin the Spray Cycle, enter the Home Menu by pressing the Home Menu Icon. 2. The Home Menu will display the current garment selection,...

Pearl Elite - Loading the Garment

Loading the garment properly will ensure even, consistent spray patterns. 1. Place the garment on the Platen as shown in the figure below with the collar of the garment towards the back of the machine. 2. Tuck the excess fabric under the platen. 3. Push the Drawer in all the...

Pearl Elite - Adjust Settings

 The settings will allow the user to control the spray density and spray length. 1. To adjust the settings, enter the Settings Menu by selecting the Settings Menu icon. 2. The Spray Density can be adjusted by pressing the Spray Density Setting and entering a value between(20 – 100). 3....

Pearl Elite - Priming the Pearl Elite

Priming the Pearl Elite is required for proper spray pattern on the garment. If the Pearl Elite is improperly primed, you may not get an even, flat and consistent spray pattern on the garment. 1. To prime the machine, enter the Maintenance Menu by selecting the Maintenance Menu icon. 2....

Pearl Elite - User Interface

Home Menu 1. Start/Stop Button Press to start or stop spray cycle. 2. Light Pretreat Level Meter Displays estimated light pretreat remaining. 3. Dark Pretreat Level Meter Displays estimated dark pretreat remaining. 4. Garment selection Displays garment selection: light or dark garment. 5. Spray Length Area Displays spray length setting....

Pearl Elite - Powering the Pearl Elite

The Pearl Elite is powered with either 110V/60Hz or 220V/50z. Please check with distributor to verify the power requirements for the Pearl Elite in your region. 1. Plug the power cord in to the power connector located on the back of the Pearl Elite. 2. Press the Power Switch to the...

Garment Printing Support

More