EMC 10 THE NEEDLE BAR WON'T COME DOWN TO SEW

Osman Bayrak

THE TAKE UP LEVER MOVES UP AND DOWN, BUT THE NEEDLE BAR WON'T COME DOWN TO SEW: Check the Jump Stitch Lever which is on the left side of the Needle Case. Make sure that the lever is not in the engaged position as seen in the Operation Manual. Another...

Troubleshooting EMC 10 MISSED HEAD UP Error: Step-by-Step Solutions

Osman Bayrak

Troubleshoot and resolve the EMC 10 MISSED HEAD UP Error on your embroidery machine with our helpful guide. This preview guides you through diagnosing and addressing the error, ensuring uninterrupted operation of your equipment.

Resolving EMC 10 NO JUMP STITCH Error: Troubleshooting Guide

Osman Bayrak

Follow these quick steps for seamless resolution and optimal functioning of your embroidery machine. Stay tuned for a hassle-free experience!

EMC 10 NOT AT HEAD UP ERROR

Osman Bayrak

NOT AT HEAD UP ERROR: The information in the section about the Z Time Out Error will be useful to determine the cause of this error. Make sure the needle case is on Color Index. Use the "Off Color Index" section for more information.  

EMC 10 OFF COLOR INDEX ERROR

Osman Bayrak

OFF COLOR INDEX ERROR: If the Red Color Change LED that can be seen atop the Color Change PCB covers is lit, take a screw driver and insert it into the hole that is on the Left side of the covers and turn the Cam left or right slowly to...

EMC 10 PICKER DOESN'T PICK UP THE THREAD

Osman Bayrak

PICKER DOESN'T PICK UP THE THREAD, CAUSING SHORT TAILS, NO TAILS, AND LONG TAILS AFTER A TRIM: Check the same pages in the technical manual as mentioned above. Thread tensions can aid in this problem also. If thread tensions are too tight Short Tails can be a problem. Make sure...

EMC 10 PICKER STAYS IN AFTER A TRIM

Osman Bayrak

PICKER STAYS IN AFTER A TRIM: Check the two tines on the Picker for burrs, as thread will catch these, and cause the thread cause the hook to wrap thread around it. The resulting error is a Z Time Out Error. If there are no burrs on the Picker, use...

EMC 10 RACK LIMIT ERROR

Osman Bayrak

RACK LIMIT ERROR: Select the correct hoop size in the Home Menu before starting the design. Use the Trace function to help avoid this problem. The Full Height Jacket Back Hoop will lose about 2 inches at the bottom of the hoop towards the front of the machine due to...

Troubleshooting EMC 10 Hoop Size Selection Errors: Quick Fixes

Dean Armando

Encountering EMC 10 errors when selecting a hoop size? No worries! Our quick troubleshooting solutions have got you covered. Learn how to address "Machine Running" or "Run Job Error" messages with easy steps, including accessing the Reset Menu and performing a system reset on the EMC 10. By following these straightforward solutions, you can ensure your embroidery machine operates seamlessly without interruptions. Stay tuned for a hassle-free resolution!

EMC 10 THE CAP FRAME IS POPPING OFF

Osman Bayrak

THE CAP FRAME IS POPPING OFF OF THE CAP FRAME DRIVER OR THE DESIGN IS BEING FLATTENED OUT NEAR AN EDGE OF THE CAP FRAME SEWING FIELD: Make sure that the Cap Frame Driver shaft is pushed in so that the metal collar is flush against the Rear Cap Frame...

EMC 10 LOOPING & BIRD NESTING

Osman Bayrak

LOOPING & BIRD NESTING: Looping can be caused by thread tensions that are to loose and it can happen on the top or bottom of the design. Both the Bobbin and Tensioners could be the cause. Check to see if the problem is the tensioners by turning the tensioner knobs...

EMC 10 GRABBER NOT HOME

Osman Bayrak

GRABBER NOT HOME: The top thread may not be trimmed under the needle plate. This will cause the Grabber to stay partially extended, and the error will show. Check the Technical Manual to see proper alignment of the Grabber System, because if the thread is cut, and the error persists...

EMC 6 / 4 Trouble Shooting Guide

Osman Bayrak

To identify the type of machine, it has 4 black sewing heads with six needles each. The serial number will start with 897_ _ _ _. THE MACHINE WON'T COME ON. THE DISPLAY IS BLANK: Check the power source. Make sure it is a working outlet. Make sure it's plugged...

EMC 10 APPLICATION RUN ERROR

Osman Bayrak

APPLICATION RUN ERROR: The EMC 10 tried to Down Load the RSA Files and it was not able to. Power off the EMC 10 and on again to retry the Down Load function. If the last operation doesn't work, configure the machine again using the information in the Operations Manual...

EMC 10 BAD CC ENCODER

Osman Bayrak

BAD CC ENCODER: Make sure the machine is configured as an EMC10 using the information in the Operations Manual. Check the Table of contents for the page listing "Configuring the EMC10". Check the same information used in the "Off Color Index" section. Replace the Color Change Bd., after checking the...

EMC 10 CAP FRAME IN

Osman Bayrak

CAP FRAME IN: This error will appear on the display if trying to set home with the Cap Frame Driver installed. If the Cap Frame Driver is not installed, then the contact or switch on the mount that indicates the driver is installed is defective or bent so it isn't...