Print Engine Blown F2 Fuse

Dean Armando

The symptoms of a blown F2 fuse are as follows: The print head will not fire a single nozzle. The machine will power up normally, and the print head carriage will move back and forth normally but not a single nozzle will fire. If any nozzles fire, then the F2...

Reseat Ink Chip Holder Anajet FP125

customer

Issues relating to the ink chip holder will result in one or more LEDs being solidly lit on the LED board under the printer's cover. Most likely the ink chips may have moved off of their contacts and need to be reseated. It is also possible that one or more...

VIDEO Learn How to Retrofit the Anajet CIS Board

customer1 comment

  Anajet Sprint CIS Assembly Board  

Adjusting or Repairing the Sprint Paper Sensor

customer

Symptoms: Printer is looping in Auto System Maintenance. Printer stuck in reset service counter (only in more severe cases), other symptoms will include print head moving to the left before print and getting stuck. Possible causes: Ink will leak down into where the carriage is located and will stain and cause errors...

VIDEO Anajet Sprint Learn How to Print on White Shirts

customer

VIDEO Learn How to Operate your Anajet Sprint

customer1 comment

Activating EK Print Studio

customer1 comment

A valid software license file is needed to run the EKPrint Studio for SPRINT program. Without a valid license file, EKPrint Studio for SPRINT will run under evaluation mode for 30 days. After the 30 day evaluation period, the print capability of EKPrint Studio for the printer will be disabled....

How and Where to Set the Ink Color Order on Anajet Sprint

customer

There are many different ways to set up the color going from your ink bay to your print head. Above you will see the tab where you change it in your program. However, in that program gives you an idea of the different configurations. Best option is the way the...

Upgrade your EKPrint Studio RIP Software for Anajet Sprint, FP125 and Melcojet

customer2 comments

If you bought a used Anajet Sprint, Anajet FP-125 or Melco Jet, it may have come with old, outdated software. It also might not work after install on your computer because it actually needs a EKPrint Studio License Transfer. Who woulda thunk..... You will need to contact http://www.eukondigital.com/transfer The upgrade...

Anajet Sprint Motherboard PCB Replacement

customer

You can buy an Anajet Sprint Motherboard PCB Replacement here Introduction This is a troubleshooting guide on how to replace a Print engine board (PCB). Scope This applies to FP-125/Sprint printers only. Symptoms Printer is looping in Auto System Maintenance. Printer stuck in reset service counter (only in more severe cases)...

VIDEO Removing the Control Panel on the Anajet Sprint

customer

Learn how to remove the control panel on the Anajet Sprint Garment Printer. Buy Parts for the Anajet Sprint Buy Ink and Supplies for the Anajet Sprint Learn more about the Anajet Sprint (1) Remove the two Phillips (+) screws that hold the Control Panel to the printer body. These...

VIDEO Installing the capping station on the Anajet Sprint

customer

Learn how to Install the Anajet Sprint Capping station.  The capping station controls pressurization and the flow of ink.  Many people think they have a clogged head when it's really the pump in the capping station or the Maintenance station is clogged.  Replace your capping station every 6 months if...

VIDEO Removing the capping station on the Anajet Sprint

customer

Learn how to remove the Anajet Sprint Capping station.  The capping station controls pressurization and the flow of ink.  Many people think they have a clogged head when it's really the pump in the capping station or the Maintenance station is clogged.  Replace your capping station every 6 months if...

Repair a clogged needle on the Anajet Sprint

customer

If the needle is really clogged, then you want to prevent the dried up ink from going to the print head or dampers. So if you are sure that there is a clog before the damper or the print head, then you are going to want to look at doing...

Anajet Auto Maintenance Loop and lock up

customer

There have been many people who have had problems with their Anajet Sprint going into an auto maintenance loop and locking up.  Through the forums I have seen many fixes or things to try offered.  The items below have been confirmed to help if not fix this problem.  If this...

Epson R1900 Anajet Exploded Diagram Schematic

customer

Epson R1900 Anajet Exploded Diagram Schematic