1. All Purpose Cleaner Used to clean the Pearl Lite after use. See “Keeping the Pearl Lite Clean” 2. Shop Rags or Towel Used to clean the Pearl Lite after use. See “Keeping the Pearl Lite Clean” 3. Distilled Water Used to clean the Pearl Lite after use. REPLACEMENT...
Pearl Lite Support
Pearl Lite - Powering the Pearl Lite
The Pearl Lite is powered with either 110V/60Hz or 220V/50z. Please check with distributor to verify the power requirements for the Pearl Lite in your region. 1. Plug the power cord in to the power connector located in the back of the Pearl Lite. 2. Press the Power Switch...
Pearl Lite - Priming the Pearl Lite
Priming the Pearl Lite is required for proper spray pattern on the garment. If the Pearl Lite is improperly primed, you may not get an even, flat and consistent spray pattern on the garment. 1. To prime the machine, enter the Prime/Purge mode by pressing the Density Up &...
Pearl Lite - Adjust Density Setting
The Density settings allows the user to control the amount of pretreat solution to apply to the garment. 1. To adjust the Spray Density, press either the Up or Down Density Button (4). 2. The Spray Density setting will be indicated by the Display. The lower limit is 20...
Pearl Lite - Loading the Garment
Loading the garment properly will ensure even, consistent spray patterns. 1. Place the garment on the Platen (5) as shown in the figure below with the collar of the garment towards the top. 2. Tuck the excess fabric under the Platen (5). 3. Push the Platen (5) in to...
Pearl Lite - Spray Cycle
The Spray Cycle is the process the Pearl Lite uses to lay a flat and even layer of pretreatment solution on to the garment. 1. With the garment loaded to the desired spray length, press the Start Button (9) to begin the Spray Cycle. 2. The Spray Cycle can be...
Pearl Lite - Flushing Pretreat Solution
When flushing pretreat solution it is important to follow these steps to ensure proper function the the Pearl Lite. These steps should be followed prior to switching pretreat solution. 1. To flush the pretreat solution, enter the prime/purge mode by pressing both the Up & Down Density Buttons (4) simultaneously....
Pearl Lite - Keeping the Pearl Lite Clean
It is important to keep the Pearl Lite clean during extended use. The pretreatment solution can build up salt deposits that can inhibit normal operation of the Pearl Lite. 1. Use shop rags or towels to regularly wipe off excess pretreatment inside the machine. 2. Use All Purpose Cleaner on...
Pearl Lite - Routine Maintenance & Adjustments
With normal use of the Pearl Lite, routine maintenance procedures will be required to follow to ensure proper operation. 1. Lubricating the Slides. If low spray densities are desired, proper lubrication of the rail system is required. 1. Spray the rail with a silicone based lubricant. 2. Move the Platen...
Pearl Lite - Troubleshooting
If you experience Possible Causes Solution Leaks Pretreatment solution dripping from Solenoid Hose may have come loose. Push hose in to quick connect Excessive pretreatment solution dripping from nozzle Nozzle Cap is loose Tighten Nozzle Cap Nozzle O-Ring is not installed Install Nozzle O-Ring Pretreatment leaking from bottom Pump Hoses...
Pearl Lite - PARTS AND FEATURES
1. Power On/Off Switch Press ( | ) to power the unit on and press (O) to turn the power off. 2. Hose Inlet Connect 1/4” OD hose to inlet for pretreatment solution supply to the Pearl Lite. 3. Display Indicates the Spray Density setting with a range between 20...
Pearl Lite - IMPORTANT SAFETY INSTRUCTIONS
Your safety and the safety of others are very important. We have provided many important safety messages in this manual. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can injure you or others. This symbol will...
